Modern living room with underfloor heating cost UK and wood floor

Underfloor Heating Cost: The Complete UK Guide for 2026

Underfloor heating is the warm floor under your feet on a cold morning. There are no radiators on the walls, no cold spots by the window, and the heat rises evenly across the whole room. It suits kitchens, bathrooms, extensions and whole houses, and it pairs well with a heat pump. But it is not a small purchase, and the price depends on the system you choose, the size of the floor and whether the house is new or already built.

The short answer is that underfloor heating cost in the UK in 2026 typically runs from £40 to £90 per square metre fitted for an electric system, and from £100 to £190 per square metre fitted for a wet system, according to MyJobQuote’s guide updated 20 October 2026. Checkatrade’s June 2026 guide is a little lower, at £50 to £75 per square metre for electric in a new build and £60 to £85 in a renovation, and £85 to £100 per square metre for wet in a new build and £95 to £110 in a renovation. Most whole jobs cost between £3,000 and £13,000, according to Checkatrade. A single bathroom can cost a few hundred pounds, while a whole house can cost £8,000 to £18,000 or more.

In this guide, we explain what underfloor heating costs in the UK, how electric and wet systems compare, what each room costs, where the money goes, which extra costs people forget, what it costs to run, how long the work takes, what rules apply, how to get a fair quote, and whether the money comes back when you sell. Everything is in plain English, with UK prices and UK rules in mind.

Table of Contents

What Is Underfloor Heating?

Underfloor heating warms a room from the floor up, instead of from a radiator on the wall. There are two types, and the type you choose decides most of the cost.

An electric system, also called a dry system, uses heating mats or cables laid under the floor. The mat is wired to a thermostat, and the electricity warms the floor directly. It is thin, quick to fit and cheap to install, which is why it suits a single room such as a bathroom or a kitchen. It runs on mains electricity, so it costs more to run than a wet system.

A wet system, also called a water system, uses a network of pipes laid under the floor. Hot water from a boiler or a heat pump flows through the pipes, and the heat rises through the floor into the room. It costs more to install, because it needs pipes, a manifold, a pump and screed or spreader plates, but it costs less to run, which is why it suits a whole house, an extension or a new build.

Both systems run at a low flow temperature, around 35 to 45 degrees, while radiators need 60 to 75 degrees. That low temperature is why underfloor heating works so well with a heat pump, and why a wet system on a gas boiler can use less energy than radiators for the same warmth. The floor finish matters too. Tile and stone carry heat well and feel warm underfoot. Wood and laminate work well if they are made for underfloor heating. Thick carpet slows the heat down, so it is not the best match.

Which Type Suits Which Home?

An electric system suits a small room in an existing home, where the floor is staying and the job needs to be quick. A bathroom, an en-suite or a kitchen is the classic case. A wet system suits a new build, an extension or a full renovation, where the floor is being laid anyway and the screed is already in the budget. It also suits a whole house, where the lower running costs pay back the higher fitting cost over time. The sections below put numbers on both choices.

How Much Does Underfloor Heating Cost in the UK?

Underfloor heating cost in the UK in 2026 depends on the system, the size of the floor and whether the home is new or being renovated. The ranges below are typical UK prices seen in 2026, drawn from Checkatrade, MyJobQuote, the Centre for Sustainable Energy, BestBuilders and other UK cost guides. They are a guide only. Prices vary by region, floor type and specification, so always get written quotes for your own home. Always ask whether a quote includes VAT, because some guides quote prices excluding VAT, and VAT at 20 percent adds a large sum to a £5,000 job.

Most UK guides agree on the shape of the answer, even if the exact numbers differ. Electric is cheaper to fit and dearer to run. Wet is dearer to fit and cheaper to run. A new build is cheaper than a renovation, because the floor is open and the screed is being laid anyway. The table below shows what the main guides say, side by side.

Cost per Square Metre by Guide

Guide Electric, per m² Wet, per m²
Checkatrade, June 2026, new build £50 to £75 £85 to £100
Checkatrade, June 2026, renovation £60 to £85 £95 to £110
MyJobQuote, October 2026, new build £40 to £80 £100 to £140
MyJobQuote, October 2026, older home £50 to £90 £150 to £190
Energy Saving Trust, October 2025 £50 to £85 £85 to £110
BestBuilders, Q3 2026 £60 to £120 £90 to £190
GS Renovation, June 2026 £50 to £85 £70 to £190

Why the Ranges Differ

The ranges differ because the guides do not all include the same things. MyJobQuote’s wet figures are the highest, mostly because they include more of the floor work, such as lifting the old floor, insulation and screed. Checkatrade’s figures are lower, but Checkatrade adds a contingency of 10 to 15 percent on top. A guide that quotes the system only, which means the mats or pipes and the fitting, will look much lower than a guide that quotes the full job, which means the system, the insulation, the screed, the controls and the floor finish. When you compare quotes, ask each installer to list what is included: the heating element or pipes, the insulation, the screed or spreader plates, the manifold and controls, the thermostat, the labour and VAT. If a quote does not list them, ask.

The Average Job

MyJobQuote puts the average underfloor heating installation cost at around £900, which is a single room average, not a whole house figure. Checkatrade puts most installations at £3,000 to £13,000, which covers anything from a few rooms to a whole house. A single bathroom can cost a few hundred pounds with an electric mat. A whole ground floor with a wet system can cost £6,000 to £13,000 or more. The sections below break each of these down.

Electric Underfloor Heating Cost

Electric underfloor heating is the cheaper system to install. MyJobQuote puts it at £40 to £90 per square metre fitted in 2026, including materials and labour. That splits into £40 to £80 per square metre in a new build and £50 to £90 per square metre in an older home. Checkatrade puts it a little lower, at £50 to £75 per square metre in a new build and £60 to £85 per square metre in a renovation. The Centre for Sustainable Energy, quoting Checkatrade, puts it at £60 to £85 per square metre. BestBuilders puts it at £60 to £120 per square metre, which is the highest of the main guides.

The cost of the mat itself is only part of the bill. Trade2Base puts an electric heating mat at £50 to £100 per square metre supplied, and a standard programmable thermostat at £100 to £200, with a WiFi thermostat at £150 to £300. Installation labour for one room runs £200 to £500, and a typical bathroom of 4 to 6 square metres costs £500 to £900 all in. Checkatrade puts DIY kits at about £20 to £50 per square metre, plus controls and insulation, for homeowners who lay the mat themselves and pay an electrician only for the connection.

Electric systems suit small rooms, and the room prices show why. MyJobQuote prices a 4 square metre en-suite at £240 to £300 for electric, and a 2 square metre cloakroom at £160 to £180. A 12 square metre kitchen costs £600 to £900 for electric, and a 20 square metre living room costs £800 to £1,200. These are fitted prices, including materials and labour, but they do not always include the thermostat, which can add £100 to £300 per zone, or the floor finish on top.

When Electric Is the Right Choice

Electric is the right choice when the room is small, the floor is staying, and the heating will be used for a few hours a day. A bathroom that is warm for an hour in the morning and an hour in the evening is the classic case. It is the wrong choice as the main heating for a whole house on a standard electricity tariff, because the running costs add up fast. That trade off is covered in the running costs section below.

Wet Underfloor Heating Cost

Wet underfloor heating costs more to install than electric, and the range is wider, because the floor work matters more. MyJobQuote puts it at £100 to £190 per square metre fitted in 2026, including materials and labour. That splits into £100 to £140 per square metre in a new build and £150 to £190 per square metre in an older home. Checkatrade puts it lower, at £85 to £100 per square metre in a new build and £95 to £110 in a renovation. GS Renovation puts it at £70 to £190 per square metre, with £70 to £100 for a new slab in an extension and £120 to £190 for a retrofit where the screed has to come up. BestBuilders puts it at £90 to £190 per square metre.

The parts cost more than the pipe. Trade2Base puts pipe, insulation board and clips at £70 to £150 per square metre supplied. A manifold unit with 4 to 8 ports costs £300 to £800, and a pump set with a blending valve costs £200 to £500. Zone thermostats and actuators cost £80 to £200 per zone. Installation labour for one room runs £800 to £1,500, and liquid screed costs £15 to £25 per square metre. Boiler Central puts the manifold lower, at £200 to £600 depending on the number of zones, and a programmable thermostat at £120 to £250.

Wet systems suit large areas, and the room prices show why. MyJobQuote prices a 12 square metre kitchen at £1,200 to £1,500 for wet, and a 20 square metre living room at £1,800 to £2,200. A 4 square metre en-suite costs £600 to £720 for wet, and a 2 square metre cloakroom costs £340 to £380. These are fitted prices, but they do not always include the insulation, the screed or the floor finish, which can add a large sum on a retrofit.

Low-Profile Retrofit Systems

A normal wet system needs depth, because the pipes sit in screed. In an existing home, that depth often does not exist, so installers use low-profile overlay boards with aluminium spreader plates. These boards sit on top of the existing floor and raise the level by only 15 to 30 mm, so doors may not need trimming. Less.co.uk puts a low-profile wet retrofit at £100 to £150 per square metre, which is dearer per square metre than a new slab, because the boards themselves cost more, even though the work is quicker and causes less mess. It is the right choice when the floor cannot come up, but the budget should allow for it.

Electric vs Wet: Which Costs Less Overall?

Electric is cheaper to fit and dearer to run. Wet is dearer to fit and cheaper to run. The question is which one gives the lower underfloor heating cost over the life of the system, and the answer depends on how big the area is and how often it is heated.

Electric (dry) Wet (water)
Fitted cost, per m² £40 to £90 £100 to £190
Fitted cost, new build £40 to £80 £100 to £140
Fitted cost, older home £50 to £90 £150 to £190
Best for Single small rooms, bathrooms, kitchens Whole house, extensions, new builds
Heat source Mains electricity Gas boiler or heat pump
Running cost About 2 to 3 times wet on gas Lower, and lower still with a heat pump
Install time 1 to 2 days per room 2 to 5 days per floor, plus screed drying
Floor height added Around 5 to 15 mm plus tile 15 to 30 mm low-profile, 80 to 100 mm with screed

For a single bathroom, electric wins. The fitting cost is a few hundred pounds, and the running cost is small because the room is heated for an hour or two a day. For a whole house, wet wins. The fitting cost is thousands of pounds more, but the running cost is far lower, and the gap grows every winter. MyJobQuote puts the running cost of electric at about twice that of wet. Retrofit Planner, working from the October to December 2026 price cap, puts a 20 square metre room at about £515 a year on electric against about £175 a year on wet with a gas boiler, which is about three times as much. The exact ratio depends on the room and the tariff, but the direction is the same in every guide: electric costs roughly double to three times as much to run as wet on gas.

A simple rule helps. If the area is under 10 square metres and it is heated now and then, choose electric. If the area is over 20 square metres, or it is heated all day, choose wet. Between 10 and 20 square metres, work out both quotes and compare the running costs over five years, not just the fitting cost.

Underfloor Heating Cost by Room

The easiest way to budget for underfloor heating is room by room. Measure the floor area of each room, then multiply by the per square metre rate for the system you want. The table below uses MyJobQuote’s room prices where they are published, and works the rest out from the per square metre rates above. Worked figures are marked, so you can see which numbers come from a guide and which are simple maths.

Room Floor area Electric, fitted Wet, fitted
Cloakroom 2 m² £160 to £180 £340 to £380
En-suite or small bathroom 4 m² £240 to £300 £600 to £720
Bathroom 5 m² £200 to £450 (worked out) £500 to £950 (worked out)
Bedroom 9 m² £360 to £810 (worked out) £900 to £1,710 (worked out)
Kitchen 12 m² £600 to £900 £1,200 to £1,500
Kitchen 14 m² £560 to £1,260 (worked out) £1,400 to £2,660 (worked out)
Living room 20 m² £800 to £1,200 £1,800 to £2,200
Kitchen-diner 25 m² £1,000 to £2,250 (worked out) £2,500 to £4,750 (worked out)

A few things to note. First, small rooms cost more per square metre than large ones, because the fixed items, the thermostat, the connection and the call-out, cost the same whatever the floor area. Second, these figures are for the heating system fitted, and they do not always include the thermostat, which adds £100 to £300 per zone, or the floor finish on top. Third, a wet system in a small room is rarely good value on its own. A 4 square metre en-suite at £600 to £720 for wet makes sense only if the wet system is already going into the rest of the house, and the en-suite is one more zone on the same manifold.

Which Rooms Suit Underfloor Heating Best?

Bathrooms and kitchens are the best rooms for underfloor heating, because they usually have tile or stone floors, which carry heat well, and because a warm floor under bare feet is the point. A living room with a wood or laminate floor works well too, if the floor is made for underfloor heating. Bedrooms work well, but the heating is used for fewer hours, so the payback is slower. A hallway is often heated as part of a whole ground floor, rather than on its own, because it is a pass-through space with little floor area to heat.

Underfloor Heating Cost for a Whole House

A whole house is where the two systems pull apart. Checkatrade gives whole house examples for 2026, and MyJobQuote gives a whole house figure for a typical three-bedroom semi. Both agree that wet costs roughly double electric to fit, and both agree that the gap is smaller in a new build than in a renovation.

House Floor area Electric, new build Electric, retrofit Wet, new build Wet, retrofit
Terraced house 75 m² £3,750 £4,500 £6,375 £7,125
Semi-detached house 90 m² £4,500 £5,400 £7,650 £8,550
Detached house 140 m² £7,000 £8,400 £11,900 £13,300

These are Checkatrade’s 2026 figures. MyJobQuote puts a 95 square metre three-bedroom semi at £3,800 to £8,550 for electric and £9,500 to £18,000 for wet, which sits close to Checkatrade at the lower end and higher at the top, because MyJobQuote includes more of the floor work in its retrofit range.

The per square metre rate falls a little as the area grows, because the fixed items, the manifold, the controls and the commissioning, are spread over more floor. But the total still rises with every room, so a whole house is a large job either way. A wet system for a whole house also needs a heat source that can run at low temperatures, which may mean a new boiler or a heat pump, and that cost sits outside the figures above. That is covered in the heat pump section below.

Where the Money Goes: Materials, Labour and Controls

The pipe or the mat is only part of the bill. On a wet system, the controls, the screed and the labour cost as much as the pipework. On an electric system, the thermostat and the electrician’s time are a large share of a small job. The table below shows where the money goes on a typical 100 square metre ground floor wet installation, using figures from HowMuchIsThat.

Part of the job Typical cost
Pipework (PE-RT or PEX pipe) £1,500 to £2,500
Manifolds and pumps £800 to £1,500
Thermostats and controls (zoning) £600 to £1,500
Installation labour £2,500 to £4,500

On top of that come the items that sit outside the heating quote: insulation, screed, the floor finish and making good. Those are covered in the extra costs section below.

Labour Costs by Trade

Labour is charged by the day, and the rate depends on the trade and the region. Trade2Base puts a plumber or heating engineer at £200 to £300 a day in most of England and Wales, rising to £300 to £400 a day in London. Boiler Central puts underfloor heating labour at £220 to £350 a day. Less.co.uk puts an electrician at £150 to £250 a day, a plumber or heating engineer at £200 to £300 a day, a floor screeder at £15 to £25 per square metre, and a tiler or floor fitter at £150 to £300 a day. Trade2Base puts UFH pipe and screed labour at £15 to £30 per square metre, manifold supply and fit at £200 to £500 depending on zones, and system commissioning and flow balancing at £100 to £200. A single-room wet installation of 20 to 30 square metres in an extension or kitchen runs to £900 to £1,800 in labour, plus materials, according to Trade2Base.

Thermostats, Manifolds and Controls

Every zone needs its own thermostat, and every wet system needs a manifold. A standard programmable thermostat costs £100 to £200, according to Trade2Base, and £120 to £250 with a floor temperature sensor, according to Boiler Central. A WiFi thermostat costs £150 to £300. Less.co.uk puts a thermostat at £100 to £300 per zone. A manifold unit with 4 to 8 ports costs £300 to £800, according to Trade2Base, and £200 to £600 depending on the number of zones, according to Boiler Central. A pump set with a blending valve costs £200 to £500. Zone thermostats and actuators cost £80 to £200 per zone. These are the parts that make the system work room by room, and they are the parts most often left out of a headline per square metre price, so check that your quote names them.

What Drives the Price Up or Down?

Two identical-looking floors can get very different quotes. Here are the factors that move the price most.

New build or renovation. A new build is the cheapest case, because the floor is open, the insulation and screed are already in the budget, and the installer is only adding pipes or mats, a manifold and controls. A renovation costs more, because the old floor has to come up, or the new system has to be built on top of it with low-profile boards. MyJobQuote’s retrofit range for wet is £150 to £190 per square metre, against £100 to £140 in a new build, which is a gap of around £50 per square metre.

Floor type. A concrete ground floor takes a screeded wet system well. A suspended timber floor needs a different detail, with spreader plates or grooved boards, and the subfloor insulation matters more. A floor that is uneven or damaged needs levelling first, which adds labour and materials.

Insulation. Heat goes down as well as up. Without insulation under the pipes or mats, you are heating the ground, and the system costs more to run for its whole life. Insulation is not optional on a new floor, and Building Regulations Part L sets a limiting U-value of 0.18 W per square metre Kelvin for a new or replacement ground floor in an extension, which works out at around 100 to 120 mm of rigid insulation board on a typical build.

Floor height. A screeded wet system adds 80 to 100 mm of height, which means doors need trimming, thresholds need adjusting and skirtings need refitting. A low-profile system adds only 15 to 30 mm, but the boards cost more. An electric mat adds around 5 to 15 mm plus tile, which is the smallest change of all.

Number of zones. Every room that is controlled on its own needs its own thermostat and, on a wet system, its own manifold port and actuator. More zones mean more controls, more wiring and more commissioning time. A single open-plan zone is cheaper than five small zones, but it is less flexible to live with.

Heat source. A wet system needs a boiler or a heat pump that can run at low temperatures. If the existing boiler is old or cannot run cool enough, it may need replacing, and that cost sits outside the underfloor heating quote. A heat pump pairs well, but it is a separate purchase, covered below.

Where you live. London and the South East cost more, because labour costs more there. A plumber’s day rate of £200 to £300 outside London rises to £300 to £400 in London, according to Trade2Base, and that gap shows in every quote.

Extra Costs People Forget

The quote is rarely the whole bill. These are the costs people forget most often, and they can add £1,000 to £3,000 or more to a job.

VAT. Some quotes exclude VAT. At 20 percent, VAT adds £1,000 to a £5,000 job. Always ask whether a quote includes VAT, and get it in writing. Energy-saving work can have different VAT treatment, so ask the installer what rate applies to your job, and do not assume.

Insulation. PIR floor insulation costs about £220 to £400 for a 10 square metre concrete floor, according to MyJobQuote. A whole ground floor of 45 square metres can need £990 to £1,800 of insulation, using the same rate. Without it, the system heats the ground as well as the room.

Screed. Screeding costs around £430 for an average room, according to MyJobQuote, and liquid screed costs £15 to £25 per square metre, according to Trade2Base. Three rooms at £430 each is £1,290, and that is before the floor finish goes on top.

Floor finish. The heating quote rarely includes the floor finish. Tiles, wood or laminate on top of the system are a separate cost, and the finish must be made for underfloor heating, or it can warp, crack or block the heat.

Removing the old floor. Lifting an old floor, disposing of it and making good the subfloor takes time and money, and it is often left out of the first quote. On a retrofit, allow for it.

Doors, thresholds and skirtings. A floor that rises by 30 mm or 80 mm means doors need trimming, thresholds need adjusting and skirtings need refitting. Each one is a small job, but together they add up.

Boiler or heat source work. A wet system may need a new manifold connection, a pump, a blending valve or a boiler that can run at low temperatures. If the boiler needs replacing, that is a separate job with its own cost.

Contingency. Checkatrade adds a contingency of 10 to 15 percent on top of its guide figures, and that is wise. On a £5,000 job, that is £500 to £750. If nothing goes wrong, the money stays in your pocket. If the subfloor is damaged or the screed needs extra work, you will be glad it is there.

What a Typical Underfloor Heating Job Costs in Total

Take three common jobs, and work each one out in full, so you can see where the money goes.

A New Extension: 20 Square Metre Living Room, Wet System

A 20 square metre living room in a new extension, with a wet system in a new slab, costs £1,800 to £2,200 fitted, according to MyJobQuote. The screed and insulation are already in the extension budget, so the heating quote covers the pipes, the manifold, the controls and the labour. Add a thermostat at £100 to £300 for the zone, and the floor finish on top, and the total for the room is around £2,000 to £2,600 before the finish.

An En-Suite: 4 Square Metre Bathroom, Electric System

A 4 square metre en-suite with an electric mat costs £240 to £300 fitted, according to MyJobQuote. Add a programmable thermostat at £120 to £250, and the total is £360 to £550 before the tiles. A typical bathroom of 4 to 6 square metres costs £500 to £900 all in, according to Trade2Base, which includes the mat, the thermostat and the labour. It is a small job, done in a day, and it is the cheapest way into underfloor heating.

A Whole Ground Floor Retrofit: 45 Square Metres, Wet System

A 45 square metre ground floor retrofit with a wet system costs £6,750 to £8,550 for the system fitted, at MyJobQuote’s retrofit rate of £150 to £190 per square metre. Add PIR insulation at £990 to £1,800, using MyJobQuote’s rate of £220 to £400 per 10 square metres, and screed for three rooms at about £430 each, which is £1,290. That gives a total of around £9,000 to £11,600 before the floor finish, the thermostat for each zone, and making good the doors and skirtings. It is a large job, and it takes the ground floor out of use for a while, but it heats the whole floor evenly for years.

Running Costs: What It Costs to Heat Your Home

The underfloor heating cost is only half the story. The running cost decides whether the system is cheap or dear to live with, and it is where electric and wet pull apart.

Checkatrade’s June 2026 running cost examples assume the heating is on for four hours a day. A 20 square metre lounge costs £0.49 an hour on electric, or £1.96 a day, against £0.26 an hour on wet, or £1.05 a day. A 14 square metre kitchen costs £0.34 an hour on electric, or £1.37 a day, against £0.18 an hour on wet, or £0.73 a day. A 5 square metre bathroom costs £0.12 an hour on electric, or £0.49 a day, against £0.07 an hour on wet, or £0.26 a day. A 9 square metre bedroom costs £0.22 an hour on electric, or £0.88 a day, against £0.12 an hour on wet, or £0.47 a day.

For a whole floor, Checkatrade puts wet underfloor heating at around £2.10 an hour, or around £1,916 a year, and electric at around £2.90 an hour, or around £2,646 a year. Radiators on gas sit at around £2.10 an hour, or around £1,916 a year, the same as wet. BestBuilders, using the April 2026 price cap, puts a 15 square metre room at £180 to £250 a year on wet, against £900 to £1,200 a year on electric. Retrofit Planner, using the October to December 2026 price cap, puts a 20 square metre room at about £515 a year on electric, against about £175 a year on wet with a gas boiler.

Why Electric Costs More to Run

The reason is the price of the fuel. The Ofgem price cap for October to December 2026 puts electricity at 26.32p per kilowatt hour and gas at 7.97p per kilowatt hour, so electricity costs more than three times as much per unit as gas. An electric floor turns every unit of electricity into heat, so it pays the full electricity rate. A wet floor on a gas boiler pays the gas rate, and a wet floor on a heat pump does better still, because the heat pump turns one unit of electricity into three or more units of heat. That is why electric is fine for a small room used for an hour a day, and a poor choice as the main heating for a whole house.

How to Keep Running Costs Down

Insulation matters more than the system. A well insulated home needs less heat, whatever the system is. A thermostat in each zone matters too, because it stops empty rooms being heated. A wet system should run at a low flow temperature, around 35 to 45 degrees, which keeps a condensing boiler in its efficient range. And the heating should be on a timer that matches how the home is used, because underfloor heating warms up slowly and cools down slowly, so short bursts of heat waste energy.

Underfloor Heating and Heat Pumps

A wet underfloor heating system and a heat pump are a natural pair. A heat pump works best at low water temperatures, and underfloor heating runs at 35 to 45 degrees, which is exactly where a heat pump is most efficient. BestBuilders puts a heat pump at a COP of 3.0 to 3.5 with underfloor heating, against 2.0 to 2.5 with radiators at 60 degrees, which means one unit of electricity gives three or more units of heat. A wet system on a gas boiler can use around 25 percent less energy than radiators for the same warmth, according to Cucumber Eco, because the low flow temperature keeps the boiler condensing.

The Boiler Upgrade Scheme helps with the heat pump itself. The scheme gives £7,500 towards an air source or ground source heat pump in England and Wales, and £9,000 for homes heated by oil or LPG with no mains gas connection, for applications up to March 2027. The installer applies for the grant, and it comes off the quote. DESNZ figures reported in 2026 put the median air source heat pump install at around £13,000 before the grant, which leaves around £5,500 after it. The grant covers the heat pump, not the underfloor heating, but the two are often fitted together, and the underfloor heating is what lets the heat pump run at its best.

If you are fitting a wet system now and plan to add a heat pump later, tell the installer. The pipe spacing, the manifold and the controls should be sized for low temperatures from the start, because changing them later means lifting the floor again.

How Long Does Installation Take?

An electric system is quick. Screwfix puts it at one to two days for the system itself, and Checkatrade gives the same for a single room. The mat goes down on insulation boards, the electrician connects the thermostat, and the tiler can usually start soon after. A single bathroom takes half a day to one day, including the thermostat wiring, according to Boiler Central.

A wet system takes longer. Screwfix puts it at three to seven days, and Checkatrade at two to five days for a single floor. Boiler Central puts a wet system in a typical three-bedroom new build at three to five days for the pipework, plus the time for the screed to cure. HowMuchIsThat puts a wet system for a whole floor at two to four days to install, plus 21 to 28 days for the screed to dry before it can be used at full temperature, and advises planning for four to six weeks in total.

The screed drying time is the part that catches people out, because it is governed by physics, not by the programme. A traditional sand and cement screed dries at roughly one day per millimetre up to 50 mm, and slower above that, so a 75 mm screed with no additive can take around 100 days to dry enough to accept a floor covering and have the heating commissioned. A fast-drying additive can bring the same screed to that point in six to seven days, and a 50 mm liquid screed is often ready in five to eight weeks. The only way to confirm it is dry enough is a hygrometer reading, not the calendar. The heating must also be brought up to temperature slowly the first time, in small steps over several days, or the screed can crack.

Plan the job around the drying time, not around the fitting time. If the floor finish is timber or vinyl, it cannot go down until the screed is dry. If the job is a renovation, plan for the room to be out of use for weeks, not days.

Do You Need Planning Permission or Building Regulations?

Most underfloor heating jobs do not need planning permission. Planning permission is about the outside of the house and its use, and underfloor heating inside the house does not change either. You need planning permission only if the work changes the outside of the house, such as building an extension for the heated room, and that permission covers the extension, not the heating.

Building Regulations do apply, and they matter for the cost. Part L covers energy efficiency, and it sets the insulation standard for a new or replacement floor. Part P covers electrical safety, and the electrical work on an electric system must be done by a qualified electrician or checked by building control. A wet system must be pressure-tested before the screed is poured, because a leak found after the screed is down is expensive to fix. Your installer should know these rules, and you should ask for the certificates when the work is done. Keep them with the house documents, because a buyer will ask for them when you sell.

If the wet system is paired with a heat pump under the Boiler Upgrade Scheme, the installer must be MCS certified, and the system must meet the MCS heat pump design standard. That is a condition of the grant, not just good practice.

Getting Quotes and Choosing an Installer

Get three written quotes from local installers, and make sure each one covers the same work. A quote should list the heating element or pipes, the insulation, the screed or spreader plates, the manifold and controls, the thermostat for each zone, the labour, and whether VAT is included. A quote that is far below the others usually leaves something out, such as the insulation, the screed or the controls. Ask each installer for recent work you can see, and for references you can call.

Check that the installer is qualified for the system you want. A wet system should be fitted by a Gas Safe registered engineer where it connects to a gas boiler, and a heat pump system should be fitted by an MCS certified installer. An electric system should be connected by a qualified electrician, and the work should meet Part P. Ask whether the work comes with a guarantee, and for how long, and get the guarantee in writing.

Ask each installer the same questions: how long will the work take, including screed drying time, who does the electrics and the screed, what happens if you find a problem under the old floor, and what is not included in the quote. The answers tell you more than the price does. A good installer will give a written schedule, a written quote and a clear payment plan. Never pay the full amount up front. A deposit to order the materials is normal, with the rest paid as the work progresses. Hold back the final payment until the system is commissioned, pressure-tested and working, and you are happy with it.

Can You Fit Underfloor Heating Yourself?

Some parts of an underfloor heating job suit a keen DIYer, and some do not. Laying an electric mat is within reach for a careful homeowner. The mat goes down on insulation boards, the cables must not cross or overlap, and the floor sensor must sit in the right place. But the final connection must be done by a qualified electrician, because the work falls under Part P of the Building Regulations. Checkatrade puts DIY kits at about £20 to £50 per square metre, plus controls and insulation, so a DIY electric job in a bathroom can cost a few hundred pounds in materials, plus the electrician’s time.

A wet system is not a DIY job for most people. It needs a manifold sized to the house, pipe loops laid to a design, a pressure test before the screed, and commissioning with flow balancing. A mistake found after the screed is poured means breaking the floor up. If you do hire trades separately, you become the project manager, and you carry the risk if one trade is late or the work does not fit together. For most people, a single installer who manages the whole job is the simpler and safer option.

A common middle path is to do the preparation yourself, such as lifting the old floor and laying the insulation boards, and to hire an installer for the pipes or mats, the manifold, the electrics and the commissioning. That can save money, but agree with the installer first what you will do and what they will do, so nothing is missed and the guarantee still stands.

Mistakes to Avoid and How to Save Money

The most expensive mistakes in underfloor heating are the ones made before the work starts. Here are the ones to avoid, and the ways to save money without cutting quality.

Skipping the insulation. Insulation under the system is not optional. Without it, heat goes down into the ground, the system costs more to run for its whole life, and the floor takes longer to warm up. Spend the money on insulation first, before spending it on a better thermostat or a dearer floor finish.

Choosing electric for a whole house. An electric system is cheap to fit and dear to run. As the main heating for a whole house on a standard tariff, it can cost two to three times as much to run as a wet system on gas. Use electric for small rooms, and wet for large areas.

Forgetting the controls. Every zone needs its own thermostat, and a wet system needs a manifold with a port for each zone. A system with one thermostat for the whole house will heat empty rooms and waste money. Budget £100 to £300 per zone for thermostats, and make sure the quote names them.

Not pressure-testing before the screed. A wet system must be pressure-tested before the screed is poured. A leak found afterwards means breaking the floor up. Ask the installer to show you the pressure test reading before the screed goes down.

Rushing the screed. A floor finish laid on damp screed will lift, warp or fail. Wait for the screed to dry, confirm it with a hygrometer reading, and bring the heating up slowly the first time. The drying time is part of the job, not a delay.

Choosing on price alone. The cheapest quote is not always the best value. A low quote may leave out the insulation, the screed, the manifold or the VAT, and the real price will appear later as extra charges. Compare what each quote includes, not just the total, and ask for the breakdown.

How to save money without cutting corners. Fit underfloor heating when the floor is being laid anyway, such as in an extension or a renovation, because the insulation and screed are already in the budget. Choose electric for a single room and wet for a whole floor. Keep the number of zones sensible, and buy the thermostat yourself only if the installer agrees. Get three quotes, and ask each installer if there is a quieter time of year when the price is lower. Do not save money by skipping the insulation, the pressure test or the contingency, because those three things cost far more to fix later.

Does Underfloor Heating Add Value?

Underfloor heating adds comfort and usable space to a home, and that is what buyers pay for. A warm floor in a kitchen or bathroom, no radiators on the walls, and even heat across the whole room all make a house nicer to live in, and easier to sell. It works best in kitchens, bathrooms and extensions, where the floor finish suits it and the room is used every day.

Whether the underfloor heating cost comes back depends on the house, the area and the system. A wet system paired with a heat pump adds more than an electric mat in a single room, because it cuts the running costs for the whole house. A wet system on a gas boiler can use around 25 percent less energy than radiators for the same warmth, which is a real saving every winter. But underfloor heating rarely returns the full fitting cost when you sell. The value is in the comfort, the even heat and the lower running costs, and in the fact that a buyer does not have to fit the system themselves. If you fit underfloor heating only to sell the house, the return may be less than the cost. If you fit it to live in, and you use it every day for years, the value is in the warm floor itself, and the sale price is a bonus. Fit the system for your own home first, and let the value follow.

Quick Takeaways

  • Underfloor heating cost in the UK in 2026 runs from £40 to £90 per m² fitted for electric, and from £100 to £190 per m² for wet, according to MyJobQuote.
  • Checkatrade puts electric at £50 to £75 per m² in a new build and £60 to £85 in a renovation, and wet at £85 to £100 in a new build and £95 to £110 in a renovation.
  • A single bathroom costs a few hundred pounds with an electric mat, while a whole house costs £3,000 to £13,000 or more, with wet roughly double electric to fit.
  • Electric is cheaper to fit and dearer to run, at roughly double to three times the running cost of wet on gas. Use electric for small rooms and wet for large areas.
  • Every zone needs its own thermostat at £100 to £300, and a wet system needs a manifold at £200 to £800, plus a pump set and screed.
  • Screed drying time is the part that catches people out: allow 4 to 6 weeks for a wet system, and confirm it is dry with a hygrometer reading.
  • Get three written quotes for the same work, ask whether VAT is included, and keep a contingency of 10 to 15 percent.

FAQs

How much does underfloor heating cost in the UK in 2026?

Underfloor heating cost in the UK in 2026 runs from £40 to £90 per square metre fitted for an electric system, and from £100 to £190 per square metre fitted for a wet system, according to MyJobQuote’s guide updated 20 October 2026. Checkatrade’s June 2026 guide puts electric at £50 to £75 per square metre in a new build and £60 to £85 in a renovation, and wet at £85 to £100 in a new build and £95 to £110 in a renovation. Most whole jobs cost between £3,000 and £13,000.

What is cheaper, electric or wet underfloor heating?

Electric is cheaper to install and wet is cheaper to run. Electric costs £40 to £90 per square metre fitted, against £100 to £190 for wet. But electric costs roughly double to three times as much to run as wet on gas, so for a large area or a whole house, wet costs less over time. For a single bathroom used for an hour or two a day, electric is the cheaper choice overall.

How much does underfloor heating cost per room?

A 4 square metre en-suite costs £240 to £300 for electric and £600 to £720 for wet, according to MyJobQuote. A 12 square metre kitchen costs £600 to £900 for electric and £1,200 to £1,500 for wet. A 20 square metre living room costs £800 to £1,200 for electric and £1,800 to £2,200 for wet. These are fitted prices, and they do not always include the thermostat, which adds £100 to £300 per zone.

How much does underfloor heating cost to run?

A 20 square metre lounge costs £0.49 an hour on electric, or £1.96 a day, against £0.26 an hour on wet, or £1.05 a day, according to Checkatrade, assuming four hours a day. For a whole floor, Checkatrade puts wet at around £2.10 an hour, or around £1,916 a year, and electric at around £2.90 an hour, or around £2,646 a year. A wet system on a heat pump costs less still, because the heat pump turns one unit of electricity into three or more units of heat.

How long does underfloor heating take to install?

An electric system takes one to two days for a single room. A wet system takes two to five days for a single floor, plus screed drying time. A traditional sand and cement screed can take four to six weeks to dry, and a 75 mm screed with no additive can take around 100 days, so plan for four to six weeks in total for a wet system, and confirm the screed is dry with a hygrometer reading before laying the floor finish.

Conclusion

Underfloor heating cost in the UK in 2026 runs from £40 to £90 per square metre fitted for an electric system, and from £100 to £190 per square metre fitted for a wet system. A single bathroom can cost a few hundred pounds with an electric mat, while a whole house costs £3,000 to £13,000 or more. The fitting cost is only half the story, because electric costs roughly double to three times as much to run as wet on gas, so the right system depends on the size of the area and how often it is heated. The controls, the insulation and the screed are a large share of the bill, and the screed drying time catches most people out, so allow four to six weeks for a wet system.

The best way to keep the cost under control is to plan before you start. Decide the system first, with electric for small rooms and wet for large areas, and fit it when the floor is being laid anyway, so the insulation and screed are already in the budget. Get three quotes for the same work, ask what each one includes, check whether VAT is included, and keep a contingency of 10 to 15 percent. A system that is planned well and fitted well will give your home warm floors, and it will suit a heat pump like no other heating. Start with the budget, get the quotes, and take the time to choose an installer you trust.

Scroll to Top